6640A REV K Norge Washer Parts List

Agitator repair kit (cam-agit)

This agitator repair kit is used to move the upper agitator and connects the base of the agitator with the agitator top mover. The kit is most commonly used if the top part of the agitator is not moving correctly but the bottom portion is. If your washer will not agitate or is noisy, you may need to replace the kit. The kit includes a medium cam, agitator dogs, bearing, thrust bearing washer, and a dust cap seal. Agitator grease is recommended for the repair, but it is not included with the agitator repair kit, it must be ordered separately. This is a genuine OEM part. Please remember to disconnect the power and water supply to the washer before starting your repair.

M series new style coil kit ('m' series boost/hold coil)

This gas dryer ignition coil set comes with two ignition coils: one three-terminal boost/hold coil, and one two-terminal secondary coil. If there is no heat or your drying time is getting longer, the coils may be bad and will need to be replaced. Once the coils go bad they do not hold the gas valve open properly. Usually only one of them burns out but you should replace them as a set. Both must be operational for the gas valve to open. This is a genuine OEM part. Please remember to disconnect the power to your dryer before starting the repair.

D-shaped knob clip (dryer metal knob clip insert)

This control knob clip helps secure the timer knob to the shaft allowing you to select the desired setting for your dryer. If the knob has become loose or the clip is missing you will need to replace the clip. This clip is a genuine OEM part, made of metal and is sold individually.

Rear drum bearing kit (rear drum bearing assembly)

This rear drum bearing kit includes one bearing, one ball shaft, one ball bearing, one ball bearing retainer, a small tube of high temperature lubricant, and installation screws. The support bearing helps support the dryer drum to rotate quietly and smoothly during operation. The bearing attaches on the inside of the rear panel of the dryer cabinet. Over time the drum bearing will wear out. This kit will help keep your dryer running as smoothly as possible with as little noise as possible. This is a genuine OEM part. Please remember to disconnect the power before starting your repair.

Bake element - 2600w 240v (elmnt-bake)

The 2600 watt 240 volts bake element is located inside the oven on the bottom to supply heat while baking. This closed hinged style bake element is 15 3/4-inch long 16 5/8-inch wide, terminal depth is 3-inch and they are 1 3/4 inches apart. If your oven is not heating evenly, the element will not heat, or there is little to no heat when baking, you may need to replace the element. This is a genuine OEM bake element. Please remember to disconnect the power to your oven before you start your repair.

Replacement ice maker

This 8-cube ice maker is used to help produce ice for your refrigerator. The ice maker receives water from the water inlet valve and will freeze the water until ice cubes are formed. Once the water has been frozen the ice cubes will be ejected from the mold into the ice bucket and will refill with water to repeat the process until the ice bucket is full. This ice maker does not include the bail or shut off arm. You can reuse the arms for your old ice maker or you can also order them separately if required. It does come complete with flat and round plug wiring harness, the mounting hardware, and the instructions. The harness can be reused. This ice maker will not fit refrigerators that have the ice auger mounted on the door. If your ice maker is not making ice you may need to replace this part. Please remember to disconnect the power and water supply before starting your repair. This ice maker is a genuine OEM part.

Middle spray arm kit

The middle wash arm rotates and distribute water inside the dishwasher. The kit has been redesigned and the supply tube is now one piece. This spray arm kit comes with an upper spray arm, holder, water supply tube, and a screw. This kit does NOT include the upper support or mount. It must be ordered separately. This is a genuine OEM part. Please remember to shut off the water supply and disconnect power to your dishwasher before starting the repair.

Drive belt (belt drive)

This dryer drum drive belt is 89.5" long and has four ribs. This part helps spin the drum during the drying cycle.

Dryer heating element (heating element (11" long x 5" wide))

When connected to electricity the dryer heating element glows red hot and generates heat. When air is blown over it, it heats the air which is used to dry the clothes. The heating element fits inside the heater housing inside the dryer. Wear and tear on the heater coil from use will eventually cause the coil to break and the element to fail. When this part fails it can cease to produce any heat. Alternately, the coil could break and short to ground allowing the dryer to continue to heat even when turned off. The latter is a fire hazard and the dryer should be disconnected from power until the element is replaced. If the element coil breaks, the element needs to be replaced. This model is 11 by 5 inches with 5/16” terminals, metal and ceramic, and comes in black. It is sold individually.

Dishwasher upper rack adjuster (adjuster)

Belt kit (washer belt kit for Maytag models. If the washer does not agitate, spin, or drain then one of the belts could be worn and require replacement.)

There are two belts under a Maytag washer; one for the main drive pulley and one for the water pump. The belt kit includes both the drive belt and the pump belt which are both V-shaped. The belt connects the drive motor to the drive system to be able to spin the tub basket. If your washer will not agitate, not spin, or not drain, the belt could be worn or damaged and will need to be replaced. This is a genuine OEM kit. Please remember to disconnect the power and shut off the water supply to your washer before starting your repair.

Evaporator fan motor (motor ac/dc evap fan)

This 115-volt 60Hz evaporator fan motor is located in the back of the freezer and circulates air over the refrigerator coils. These coils will convert the heat into cool air, which is then circulated. If the motor has failed, the freezer/refrigerator will become too warm because the fan motor is not circulating the cool air from the freezer into the refrigerator. This is a genuine OEM part. Please remember to disconnect the power to the appliance before starting your repair.

Dishwasher upper dish rack wheel mount (wheel)

This part is located on the top dish rack with two per side. It is sold individually. This upper dish rack wheel mount can be used on either side of your dish rack. It is sold individually. The part includes the wheel and support, which attaches to the dish rack and allows it to slide in and out easily

Front drawer glide (use 3051162)

This front drawer glide is for your bottom range drawer. As the broiler drawer slides back and forth, these glides prevent metal-to-metal contact and offer support for the drawer. If you are having trouble opening and closing the broiler drawer, the glide may be broken and will need to be replaced. Your range has 4 in total – 2 front and 2 rear. This is a genuine OEM part and is sold individually.

Upper rack wheel with mount (wheel)

This wheel and mount assembly is located on the upper dishwasher rack to allow you to slide the rack in and out easily. They are sold individually; four are usually required for your model. Also known as stationary wheel mount. This is a genuine OEM part.